DC/DC Converters TEN 30WI Series, 30 Watt Features Ultra wide 4:1 input voltage range Single output voltage models from 1.8 to 15 VDC Dual output voltage models Extended operating temperature range: -40C to 85C Under voltage lockout Remote On/Off Shielded metal case with insulated baseplate Optional heatsink Lead free design - RoHS compliant 3-year product warranty The TEN 30WI series is a family of high performance 30W dc-dc converters featuring ultra wide 4:1 input voltage ranges in a compact low profile package with industry-standard footprint. A very high efficiency allows operating temperatures up to 85C. A built-in filter for both input and output minimizes the need for external filtering. Further standard features include remote On/Off, output voltage trimming, over voltage protection, under voltage lockout and short circuit protection. Typical applications for these products are battery operated equipment and distributed power architectures in communication and industrial electronics, everywhere where isolated, tightly regulated voltages are required and space is limited on the PCB. Models Order code Input voltage range Output voltage Output current max. Efficiency typ. TEN 30-2408WI 1.8 VDC 8`000 mA 80 % TEN 30-2409WI 2.5 VDC 8'000 mA 85 % TEN 30-2410WI 3.3 VDC 6'000 mA 87 % TEN 30-2411WI 10 - 40 VDC 5.0 VDC 6`000 mA 87 % TEN 30-2412WI (nominal 24 VDC) 12 VDC 2'500 mA 87 % TEN 30-2413WI 15 VDC 2'000 mA 88 % TEN 30-2422WI 12 VDC 1'250 mA 85 % TEN 30-2423WI 15 VDC 1'000 mA 86 % TEN 30-4808WI 1.8 VDC 8`000 mA 81 % TEN 30-4809WI 2.5 VDC 8'000 mA 86 % TEN 30-4810WI 3.3 VDC 6'000 mA 87 % TEN 30-4811WI 18 - 75 VDC 5.0 VDC 6`000 mA 88 % TEN 30-4812WI (nominal 48 VDC) 12 VDC 2'500 mA 87 % TEN 30-4813WI 15 VDC 2'000 mA 88 % TEN 30-4822WI 12 VDC 1'250 mA 86 % TEN 30-4823WI 15 VDC 1'000 mA 87 % http://www.tracopower.com Page 1 of 4 DC/DC Converters TEN 30WI 30 Watt Input Specifications Input current at no load (nominal input 24/48 Vin) 1.8 Vout models: 35 / 20 mA typ. 2.5/3.3 Vout models: 40 / 25 mA typ. other models: 70 / 45 mA typ. Input current at full load (nominal input 24/48 Vin) 1.8 Vout models: 760 / 380 mA typ. 2.5/3.3 Vout models: 1030 / 510 mA typ. other models: 1500 / 750 mA typ. Input voltage variation (dv/dt) 5 V/ms, max. (complies with ETS 300 132 part. 4.4) Start-up voltage / under voltage lockout 24 Vin models: 10 VDC / 8 VDC (typ.) 48 Vin models: 18 VDC / 16 VDC (typ.) Surge voltage (100 msec. max.) 24 Vin models: 50 V max. 48 Vin models: 100 V max. Conducted noise (input) EN 55022 level A, FCC part 15, level A with external capacitor (see note 1) ESD (input) EN 61000-4-2, perf. criteria B Fast transient (input) EN 61000-4-4, perf. criteria A Surge (input) EN 61000-4-5, perf. criteria B Output Specifications Voltage set accuracy 1 % Output voltage adjustment 10 % Regulation - Input variation Vin min. to Vin max. 0.5 % max. - Load variation 10 - 100 %: single output models: 0.5 % max. dual output models: 1.0 % max. (balanced load) 5 % max. (Load cross variation 25 % / 100 %) Temperature coefficient 0.02 %/K Ripple and noise (20 MHz Bandwidth): 75 mVpk-pk max. Start up time (nominal Vin and constant resistive load) 10 ms typ. Transient response setting time (25% load step change) 300 s typ. Short circuit protection indefinite (automatic recovery) Over load protection 150 % of Iout max typ. foldback Thermal shutdown at +115C typ Over voltage protection 1.8, 2.5 & 3.3 V output 5.0 V output 12 V output 15 V output models: models: models: models: 3.9 V 6.2 V 15 V 18 V Minimum load (only for dual output models) 10% of rated max current (operation at lower load condition will not damage these converters, however, they may not meet all listed specifications) Capacitive load 1.8 / 2.5 Vout models: 3.3 / 5.0 Vout models: 12 / 15 Vout models: 12 / 15 Vout models: 65'000 F max./ 33'000 F max. 19'500 F max./ 10'200 F max. 3'300 F max./ 1'100 F max. 1'000 F max./ 680 F max. (per output) All specifications valid at nominal input voltage, full load and +25C after warm-up time unless otherwise stated. http://www.tracopower.com Page 2 of 4 DC/DC Converters TEN 30WI 30 Watt General Specifications Temperature ranges - Operating -40C to +85C (with derating) - Case temperature +100C max. - Storage -55C to +105C Thermal impedance - with heat-sink TEN-HS2 8.24 K/Watt - without heat-sink 10 K/Watt Humidity (non condensing) 95 % rel H max. Reliability, calculated MTBF (MIL-HDBK-217F, at +25C, ground benign) >750'000 h Isolation voltage (60sec.) - Input / Output 1`500 VDC Isolation resistance - Input / Output >1`000 M Ohm Isolation capacitance - Input / Output 1000 pF max. Remote On/Off - On: 3.5 ... 12 VDC or open circuit. - Off: 0 ... 1.2 VDC or short circuit pin 3 and pin 2 - Off idle current: 3 mA typ. Switching frequency 300 kHz typ. (pulse width modulation PWM) Vibration 10-55 Hz, 2G, 30 minutes along X,Y,Z Safety approvals UL 60950, IEC/EN 60950, compliance up to 60 VDC input voltage (SELV limit) - Certification documents www.tracopower.com/overview/ten30wi Environmental compliance - Reach www.tracopower.com/info/reach-declaration.pdf - RoHS RoHS directive 20011/65/EU Supporting documents: www.tracopower.com/overview/ten30wi Note 1: In order to meet conducted emissions EN55022-A and EN55011-A a capacitor between +Vin and -Vin has to be installed. The capacitor should be capable to handle 1 A ripple current. A suggestion is KMF Series of Nippon chemi-con, 220F/100V, ESR 90mOhm. Output Voltage Adjustment Trim Trim up Trim down +Vout Ru Rd - Vout Trim Ru [kohm]* output +5% +10% output +5% +10% Ru [kohm]* 1.8V 2.5V 1.2 4.3 0.068 0.82 12V 47 8.2 15V 47 6.8 3.3V 6.8 1.5 5.0V 4.7 0.56 output -5% -10% 1.8V 1.8 0.1 2.5V 6.8 0.82 3.3V 8.2 0.68 5.0V 5.6 0.68 12V 15V 27 33 2.2 2.7 output -5% -10% 12V 56 5.6 15V 56 2.2 12V 15V 33 39 2.7 3.3 *approximate values All specifications valid at nominal input voltage, full load and +25C after warm-up time unless otherwise stated. http://www.tracopower.com Page 3 of 4 DC/DC Converters TEN 30WI 30 Watt Physical Specifications Casing material copper, nickel plated Baseplate material none conductive FR4 Potting material epoxy (UL 94V-0 -rated) Weight 48 g (1.69 oz) Soldering temperature max. 265C / 10 sec. 4 45.72 (1.8) (0.22) (0.4) (0.5) 12.7 (0.4) 2 1 (0.2) 5 Bottom view Pin-Out 10.16 6 3 5.08 (0.4) (0.4) (0.4) 7 (0.2) 5.1 5.6 10.2 10.16 10.16 10.16 40.6 (1.6) Outline Dimensions Pin Single Dual 1 +Vin (Vcc) +Vin (Vcc) 2 -Vin (GND) -Vin (GND) 3 4 +Vout 5 +Vout Common 6 -Vout -Vout 7 50.8 (2.0) Remote On/Off No pin Trim Dimensions in [mm], () = Inch Pin diameter: 1.0 0.05 (0.02 0.002) Pin pitch tolerances: 0.35 (0.014) Case tolerances: 0.5 (0.02) Heat-sink TEN-HS2 Order code: TEN-HS2 (cont.: heat-sink, thermal pad, 2 clamps) Material: Aluminum Finish: Anodic treatment (black) Weight: 19 g (0.67oz) (without converter) 56.0 (2.2) max. Heat-sink Thermal pad Clamp Converter 23.0 (0.9) 17.2 (0.68) max. Note: The product label on converter has to be removed before mounting the heat-sink. For volume orders converters will be supplied with heat-sinks already mounted. Please contact factory for quotation. Separate heat-sinks are only available for prototypes and small quantity orders. Specifications can be changed without notice! Make sure you are using the latest documentation, downloadable at www.tracopower.com Rev. July 13, 2018 www.tracopower.com Page 4 of 4 Mouser Electronics Authorized Distributor Click to View Pricing, Inventory, Delivery & Lifecycle Information: TRACO Power: TEN 30-4811WI TEN 30-2412WI TEN 30-2410WI TEN 30-2413WI TEN 30-2411WI TEN 30-4810WI TEN 304808WI TEN 30-4822WI TEN 30-2423WI TEN 30-4823WI TEN 30-2422WI TEN 30-4812WI TEN 30-2409WI TEN 30-4809WI TEN 30-2408WI TEN 30-4813WI